pondglove6

Fiat 500 Replacement Key Fob It's possible to change the battery if your 500 remote key fob is not working. If you do replace the battery and it is still not working, then the problem is probably elsewhere. United Locksmith specializes in the creation of new keys for classic automobiles. We have all the tools and components needed for this service. Dead Coin Battery The most frequent reason why your Fiat 500 key fob will not lock or unlock the doors is due to a dead battery. The key fob is equipped with the battery of a coin-cell that can quickly deplete when it isn't frequently used. If your remote began to show signs of weakening such as a loss of range or stopped working completely it is likely that the battery is dead. The battery inside the key fob is secured by metal clips that hold it in place. If the clips aren't tight, they can cause problems with contact that can prevent your remote to receive power. By using a small flathead screwdriver, push the retaining clip to remove the battery, and replace it with a brand new one. Make sure to select an identical replacement battery type of voltage, dimensions, and specification as the original battery. The key fob might also be damaged or corroded due to exposure to water. Even a short bath in soapy, warm water could damage the chip. Keep your key fob dry. Water Damage Damage to your water supply could be the reason for your key fob not working properly. Key fobs are fitted with rubber seals to protect them from being damaged by rain or splashes of water. However, it is vital to keep your keys out of the ocean, pool, and washing machine! The key fob contains an electronic chip which sends an immobilizer system in your car. key fiat 500 allows the 500 to be locked and started. If it gets wet, however it won't function. You can try cleaning the inside electronics of your keyfob with isopropyl Alcohol or an electronic cleaner to see whether they're still working. However, it's better to purchase a replacement from a dealer rather than trying to fix a key fob that was submerged in salt water. Although a replacement fob may cost you a little bit of money, it's far less expensive than paying for your Fiat 500 to be towed to the dealer and repaired! You can also make it yourself with just a few steps. Make sure you have the correct battery type before attempting to open your key fob. You can find step-bystep directions for any car keyfob online. Faulty Chip The chip inside the key fob communicates with your vehicle's immobiliser to ensure that the vehicle is only able to start when the correct key is inserted. If the chip is damaged, or damaged in any way, your car will not start. A chip that is damaged can happen due to many reasons, but the most common cause is water damage or the battery being dead. Whatever the reason, it is best to delegate this work to a locksmith as they will be able to replace the chip for you swiftly and at a low cost. If your key fob ceases to function after exposure to clean water from the tap or rain, take off the battery and clean the electronic component with a tissue to ensure it is fully dry before putting it back into. If the key fob does not work it's most likely to be a damaged chip and will require replacement. Some people will visit their dealer if they require an entirely new Fiat fob. However, this can be costly. United Locksmith is the best option if you are looking to have your Fiat key fob replaced at a reasonable cost. We have the tools and knowledge necessary to fix your Fiat key fob in a timely and professional manner. Faulty Receiver Module Fiat key fobs transmit signals of up 50 feet to the vehicle, which can unlock and lock the doors (and start the vehicle if it has automatic transmissions). However there are several things that could cause the fob to stop working. This can be caused by a dead coin-battery, water damage, worn out buttons, a receiver issue, signal interference or a malfunctioning chip. If the fob was located in the pocket of someone who has suffered extreme trauma (such as being dropped onto the floor, or washed in the washing machine) it might not be in a position to connect with the Body Control Module (BCM) of the car. This is because the BCM is secured and will only accept a signal from a genuine original key and not another. If this is the case, then you will need to replace your fob. A professional locksmith can handle the entire key replacement process including programming a new key for your 500. In fact, they can even provide you with a clone key that functions like your original fob (and costs a fraction of the price).